centos7创建ftp服务器

个人博客地址http://xgs888.top/post/view?id=94；由于测试需要把文件传到对方的ftp服务器上面，需要一个测试环境，然后就鼓捣了一个ftp服务器；记录一下环境centos7 1:检查是否安装了vsftpd[cpp] view plain copyrpm -q vsftpd  2:就直接进入安装流程[php] view plain copyyum install vsftpd  -y  3:开启服务[php] view plain copysystemctl start vsftpd.service  4:开机自启动[php] view plain copysystemctl enable vsftpd.service  5:修改配置文件[php] view plain copyvi /etc/vsftpd/vsftpd.conf  贴出我的配置# Example config file /etc/vsftpd/vsftpd.conf## The default compiled in settings are fairly paranoid. This sample file# loosens things up a bit, to make the ftp daemon more usable.# Please see vsftpd.conf.5 for all compiled in defaults.## READ THIS: This example file is NOT an exhaustive list of vsftpd options.# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's# capabilities.## Allow anonymous FTP? (Beware - allowed by default if you comment this out).anonymous_enable=YES## Uncomment this to allow local users to log in.# When SELinux is enforcing check for SE bool ftp_home_dirlocal_enable=YES## Uncomment this to enable any form of FTP write command.write_enable=YES## Default umask for local users is 077. You may wish to change this to 022,# if your users expect that (022 is used by most other ftpd's)local_umask=022## Uncomment this to allow the anonymous FTP user to upload files. This only# has an effect if the above global write enable is activated. Also, you will# obviously need to create a directory writable by the FTP user.# When SELinux is enforcing check for SE bool allow_ftpd_anon_write, allow_ftpd_full_access#anon_upload_enable=YES## Uncomment this if you want the anonymous FTP user to be able to create# new directories.#anon_mkdir_write_enable=YES## Activate directory messages - messages given to remote users when they# go into a certain directory.dirmessage_enable=YES## Activate logging of uploads/downloads.xferlog_enable=YES## Make sure PORT transfer connections originate from port 20 (ftp-data).connect_from_port_20=YES## If you want, you can arrange for uploaded anonymous files to be owned by# a different user. Note! Using "root" for uploaded files is not# recommended!#chown_uploads=YES#chown_username=whoever## You may override where the log file goes if you like. The default is shown# below.#xferlog_file=/var/log/xferlog## If you want, you can have your log file in standard ftpd xferlog format.# Note that the default log file location is /var/log/xferlog in this case.xferlog_std_format=YES## You may change the default value for timing out an idle session.idle_session_timeout=600## You may change the default value for timing out a data connection.data_connection_timeout=120## It is recommended that you define on your system a unique user which the# ftp server can use as a totally isolated and unprivileged user.#nopriv_user=ftpsecure## Enable this and the server will recognise asynchronous ABOR requests. Not# recommended for security (the code is non-trivial). Not enabling it,# however, may confuse older FTP clients.#async_abor_enable=YES## By default the server will pretend to allow ASCII mode but in fact ignore# the request. Turn on the below options to have the server actually do ASCII# mangling on files when in ASCII mode.# Beware that on some FTP servers, ASCII support allows a denial of service# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd# predicted this attack and has always been safe, reporting the size of the# raw file.# ASCII mangling is a horrible feature of the protocol.ascii_upload_enable=YESascii_download_enable=YES## You may fully customise the login banner string:ftpd_banner=Welcome to blah FTP service.## You may specify a file of disallowed anonymous e-mail addresses. Apparently# useful for combatting certain DoS attacks.#deny_email_enable=YES# (default follows)#banned_email_file=/etc/vsftpd/banned_emails## You may specify an explicit list of local users to chroot() to their home# directory. If chroot_local_user is YES, then this list becomes a list of# users to NOT chroot().# (Warning! chroot'ing can be very dangerous. If using chroot, make sure that# the user does not have write access to the top level directory within the# chroot)chroot_local_user=YES#chroot_list_enable=YES# (default follows)#chroot_list_file=/etc/vsftpd/chroot_list## You may activate the "-R" option to the builtin ls. This is disabled by# default to avoid remote users being able to cause excessive I/O on large# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume# the presence of the "-R" option, so there is a strong case for enabling it.ls_recurse_enable=YES## When "listen" directive is enabled, vsftpd runs in standalone mode and# listens on IPv4 sockets. This directive cannot be used in conjunction# with the listen_ipv6 directive.listen=YES## This directive enables listening on IPv6 sockets. By default, listening# on the IPv6 "any" address (::) will accept connections from both IPv6# and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6# sockets. If you want that (perhaps because you want to listen on specific# addresses) then you must run two copies of vsftpd with two configuration# files.# Make sure, that one of the listen options is commented !!#这个一定要注释；否则启动会报错#listen_ipv6=YESpam_service_name=vsftpduserlist_enable=YESuserlist_deny=NOlocal_root=/ftpservertcp_wrappers=YESuse_localtime=YESallow_writeable_chroot=YES6：添加用户 useradd xiaoxie -s /sbin/nologin7:修改密码passwd xiaoxie然后输入密码8：编辑用户列表；vi /etc/vsftpd/user_list9：为用户分配目录和权限mkdir /ftpserverchown -R xiaoxie /ftpserverchmod -R 777 /ftpserver10:关闭setlinuxvi /etc/selinux/config11:重启服务systemctl restart vsftpd.serviceftp登录成功；